Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
What're your opinions concerning How to Install a Bathtub?
Installing a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard project. If the old bathtub is easily obtainable, the task can move quickly; if you have to open a wall surface to eliminate the old tub and position the brand-new bath tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and also fit trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is better to consider utilizing one before you begin. Opportunities are you might need an expert plumber to make tube links.
This post will certainly assist you mount a brand-new bathtub in your bathroom if you have actually already purchased a brand-new bathtub and also do not require to alter the setup of your previous water system pipes.
Your devices as well as material checklist ought to consist of the following:
Preparing for the Installation
To start with, the supporting frame provided with the bathroom must be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the flexible faucet connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the restricted accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing both wood boards under its feet, position the tub in the needed position. The wooden boards are handy in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the tub up until the spirit level reads level.
To set up taps, fit the bottom of the outermost flexible tap port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and also inspect all joints as well as new pipework for leaks as well as tighten them if essential. Fill the tub and also inspect the overflow outlet as well as the typical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bath tub needs to wait till the bathtub has actually been used a minimum of when as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washers are in area in between the faucet and the sink. Safeguard the faucet in position with the supplier given backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap adapters. The former type needs to be connected to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in problems with dampness and also possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our piece about How to Install a Bathtub Yourself. Thank you so much for spending some time to read our blog. Do you know another individual who is fascinated by the topic? Feel free to share it. Thank you for taking the time to read it.
Book 24/7 Report this page